# PVC and CPVC technical reference

V2 (fact-checked from V1)

## Dimensions: nominal names, published average ID, and minimum wall

All dimensions below are inches. OD means outside diameter; ID means inside diameter. Nominal size is a name, not measured OD. Published average ID is a manufacturer reference, not a guaranteed minimum bore; do not derive average ID from OD minus twice the minimum wall. Confirm the selected product’s dimensions and dimensional tolerances.

IPS PVC/CPVC reference (GF Harvel S1): ½-inch Schedule 80 — OD 0.840 in; minimum wall 0.147 in; published average ID 0.526 in. ¾-inch Schedule 80 — OD 1.050 in; minimum wall 0.154 in; published average ID 0.722 in.

Schedule 40 comparison: ½-inch — OD 0.840 in; minimum wall 0.109 in; average ID 0.602 in. ¾-inch — OD 1.050 in; minimum wall 0.113 in; average ID 0.804 in. Schedule 80 has a thicker wall and smaller opening at the same nominal size.

## ½-inch CPVC: IPS or CTS?

Ask which sizing system is intended. ½-inch IPS Schedule 80 CPVC has OD 0.840 in. ½-inch CTS CPVC SDR 11 has OD 0.625 in and does not fit ½-inch IPS fittings. CTS is a tubing size/SDR series, not Schedule 80.

ASTM D2846 Table 1 (S4) minimum wall: ½-inch CTS 0.060 in; ¾-inch CTS 0.080 in, with OD 0.875 in for ¾-inch. Spears S3 prints 0.068 in minimum wall and approximately 0.469 in average ID for its ½-inch CTS product; its ¾-inch product has minimum wall 0.080 in and average ID 0.695 in. The ASTM minimum and the manufacturer product table are different references; check the actual product print line and technical sheet. Do not calculate or assume a guaranteed bore from either minimum wall.

## Temperature and pressure: reference values

PVC maximum service temperature: 140°F (60°C). Industrial IPS CPVC: up to 200°F (approximately 93°C). D2846 CTS CPVC hot/cold water systems: up to 180°F (approximately 82°C), rated 100 psi at 180°F in the cited CTS reference. Do not apply the 200°F IPS limit to CTS. PVC is not permitted for hot potable-water distribution under IPC 2021 Table 605.4; code adoption and the selected product must be checked for a real installation.

Reference water pressures at 73°F (approximately 23°C), plain-end pipe used with properly made solvent-welded connections: ½-inch IPS Schedule 40 600 psi, Schedule 80 850 psi; ¾-inch IPS Schedule 40 480 psi, Schedule 80 690 psi (S1). CTS CPVC SDR 11: 400 psi at 73°F (S3). These are reference ratings for the cited pipe. Confirm the rating of the finished component and system; the lowest-rated component and service conditions govern.

Temperature derating factors relative to the cited 73°F plain-end pressure: PVC — 100°F ×0.62; 120°F ×0.40; 140°F ×0.22. IPS CPVC — 100°F ×0.82; 140°F ×0.50; 180°F ×0.25; 200°F ×0.20 (S1). Multiply, do not subtract. Apply manufacturer limits and connection reductions as well; this IPS table is not authorization for CTS operation at 200°F. Confirm selected-product availability and certification, and the required finished component and system ratings.

## Cutting, threads and chamfers

A square cut alone does not invoke a pressure derating factor: cutting to length leaves the wall intact. Damage, end preparation and connection quality still matter; it does not certify the resulting assembly.

Use dies designed for plastic. Specify the thread designation and acceptance/gage requirements for each end independently.

Rule: GF Harvel S1 specifies a 50% reduction of the manufacturer’s plain-end water-service pressure rating at 73°F when cutting threads into suitable Schedule 80-or-heavier PVC/CPVC IPS pipe.

Reference examples: ½-inch Schedule 80 is 850 × 0.50 = 425 psi; ¾-inch Schedule 80 is 690 × 0.50 = 345 psi, before other applicable reductions. These reference calculations do not establish a finished component or system rating.

Limitations: Confirm manufacturer, product, temperature, conveyed substance, concentration, operating pressure and connection limitations. This rule does not apply universally to every plastic or to molded threaded fittings. Cut threads only on suitable Schedule 80 or heavier IPS pipe; do not cut NPT threads on Schedule 40 or CTS tubing. Specify ASME B1.20.1 / ASTM F1498 dimensions and gaging; F1498 is not pressure certification.

GF Harvel advises avoiding standard threaded joints above 110°F for PVC and 150°F for CPVC. Apply approved, plastic-compatible tape or compound to male threads only, following the product instructions; avoid overtightening.

Rule: Follow the selected manufacturer’s product- and size-specific end-preparation instructions.

Source example: IPEX S12, printed pages 47 and 51 (PDF pages 56 and 60), shows a 10–15 degree OD bevel with approximately 3/32 inch (0.09375 inch) AXIAL EXTENT, measured along the pipe axis, not radial depth. The accompanying instructions address pressure pipe 2 inches and above.

Limitations: Do not assign this geometry by default to the ½-inch or ¾-inch examples. Confirm achievable chamfer dimensions with the selected manufacturer or fabricator. The undimensioned chamfer drawing illustrates shape only.

TOE means threaded one end; TBE means threaded both ends. These are supplier ordering conventions, not ASTM-defined product terms. State end A and end B explicitly, including the treatment of any plain end.

## Joining, potable certification and intended service

For PVC solvent joints use D2564 cement and F656 primer as required by code/system instructions. For CPVC use F493 cement and the manufacturer’s primer or approved one-step method. IPC 605.9 prohibits solvent-cement joints between different types of plastic; use an approved transition rather than directly solvent-joining PVC to CPVC.

The cited pressure-pipe standards D1785, F441 and D2846 concern liquid service. Do not transport, store or pressure-test with compressed air or gas. Potable suitability requires the actual product’s NSF/ANSI/CAN 61 conformity and applicable code compliance; confirm certification of the selected product.

## Chemical compatibility and flow

CPVC is generally very poor with ammonia and amines. PVC may be better for some ammonia solutions; do not extend that comparison to all amines. Ketones, esters, aromatic and chlorinated solvents are generally unsuitable for PVC/CPVC. Compatibility depends on the exact substance, concentration and temperature; consult the selected manufacturer’s table and PPI TR-19 (S13/S14), not a blanket family-level claim.

Illustrative friction comparison at the same flow rate, straight length and Hazen–Williams C: head loss varies approximately as ID to the power −4.8655. Using the cited average bores, ½-inch Schedule 80 versus Schedule 40 is (0.602/0.526)^4.8655 ≈ 1.93, or about 2×. ½-inch CTS versus Schedule 40 is (0.602/0.469)^4.8655 ≈ 3.37, or about 3.4×. These are calculated comparisons, not measured performance or fitting-loss estimates. Keep design velocity at or below 5 ft/s as conservative water-service guidance; confirm the manufacturer’s design requirements and surge limits.

## Standards glossary

ASTM D1784: Compound cell classification for rigid PVC/CPVC; not a pipe dimensional standard.

ASTM D1785: PVC IPS Schedule 40, 80 and 120 pipe, intended for pressurized liquids.

ASTM F441/F441M: CPVC IPS Schedule 40 and 80 pipe, intended for pressurized liquids.

ASTM D2846/D2846M: CPVC hot/cold water distribution systems, including CTS SDR 11 tubing, through 180°F.

ASTM D2665: PVC drain, waste and vent (DWV) pipe/fittings; non-pressure service.

ASME B1.20.1 / ASTM F1498: NPT geometry; F1498 specifies tapered pipe-thread dimensions and gaging for thermoplastic pipe/fittings, not pressure ratings.

NSF/ANSI 14: Plastic piping product performance and related certification requirements.

NSF/ANSI/CAN 61: Drinking-water contact health effects; IPC 605.4 requires NSF 61 conformity for potable water distribution piping. Confirm certification of the selected product.

ASTM D2564: PVC solvent cement.

ASTM F656: Primer for solvent-cement joining of PVC/CPVC; use as required by the system instructions and code.

ASTM F493: CPVC solvent cement; primer or approved one-step method depends on product/system instructions.

## Sources

S1: GF Harvel / GF Piping Systems Vinyl Catalog and Technical Information, printed p. 8 dimensions; temperature/pressure, fabrication and friction sections
https://www.gfps.com/content/dam/gfps/us/other/archive/gfps-us-brochure-Vinyl-Catalog-and-Tech-Information-2024-en.pdf

S3: Spears CTS CPVC Design and Installation, temperature/pressure and pipe-dimension table (PDF p. 17)
https://www.spearsmfg.com/super_sourcebook/SSB-1%20Part%202%20Technical%20Information%20Catalog/082%20CPVC%20CTS%20Pipe,%20Fittings%20&%20Valves%20Design%20&%20Installation.pdf

S4: ASTM D2846/D2846M-24, scope and Table 1; Table 1 checked in the ASTM-authored excerpt linked separately
https://store.astm.org/d2846_d2846m-24.html
ASTM-authored Table 1 excerpt: https://standards.iteh.ai/catalog/standards/astm/7f512710-d2d3-4f0a-a756-339c63433775/astm-d2846-d2846m-24

S7: IPC 2021 Chapter 6: 605.4, 605.9, 605.14.3, 605.21.3–4; reference code, not a determination of local adoption
https://codes.iccsafe.org/content/IPC2021P1/chapter-6-water-supply-and-distribution

S12: IPEX Vinyl Process Technical Manual, printed pages 47 and 51 (PDF pages 56 and 60): axial chamfer extent and pressure-pipe preparation for 2 inches and above
https://ipexna.com/wp-content/uploads/2026/04/industrial-tech-manual-usen-ipex-vinyl.pdf

S13: PPI TR-19, chemical resistance; check the specific chemical and service conditions
https://plasticpipe.org/tr-19

S14: Charlotte Pipe Plastics Technical Manual, chemical table and flow velocity guidance
https://www.charlottepipe.com/uploads/documents/technical/TM-PL.pdf

S15: NSF/ANSI 14 versus NSF/ANSI/CAN 61 certification guidance
https://www.nsf.org/knowledge-library/certification-of-plastic-piping-products-nsf-ansi-14-and-nsf-ansi-can-61
