{
  "notice": "Hypothetical requests. Product suitability and manufacturing capability require confirmation. Null means unknown.",
  "schema": "pipe-specification.schema.json",
  "examples": [
    {
      "id": "plain-pvc",
      "title": "Ten plain-end PVC pieces",
      "request": "Ten pieces of half-inch nominal IPS Schedule 80 PVC, each 6 inches finished end-to-end, square cut at both ends, required length tolerance ±1/32 inch.",
      "specification": {
        "material": "PVC",
        "nominal_size": "1/2 in",
        "sizing_system": "IPS",
        "actual_od_requirement": null,
        "schedule": "80",
        "finished_length": {
          "value": 6,
          "unit": "in"
        },
        "required_tolerance": {
          "plus_minus": 0.03125,
          "unit": "in"
        },
        "end_a": "square_cut",
        "end_b": "square_cut",
        "quantity": 10,
        "in_research_scope": true,
        "clarifications": [
          "Confirm stock technical sheet, intended application and achievable tolerance before sourcing.",
          "The example states a requested tolerance; confirm that the selected process can meet it.",
          "Ask for conveyed substance, concentration, operating temperature and pressure; no material is selected from a vague application label.",
          "Schema success records structure only, not completeness, suitability or manufacturability."
        ],
        "source_refs": [
          "https://www.gfps.com/content/dam/gfps/us/other/archive/gfps-us-brochure-Vinyl-Catalog-and-Tech-Information-2024-en.pdf"
        ],
        "original_request": "Ten pieces of half-inch nominal IPS Schedule 80 PVC, each 6 inches finished end-to-end, square cut at both ends, required length tolerance ±1/32 inch.",
        "sdr": null,
        "application": null
      }
    },
    {
      "id": "different-ends-cpvc",
      "title": "CPVC with different ends",
      "request": "Two pieces of three-quarter-inch nominal IPS Schedule 80 CPVC, 8 inches finished end-to-end, male 3/4–14 NPT on end A, chamfer on end B.",
      "specification": {
        "material": "CPVC",
        "nominal_size": "3/4 in",
        "sizing_system": "IPS",
        "actual_od_requirement": null,
        "schedule": "80",
        "finished_length": {
          "value": 8,
          "unit": "in"
        },
        "required_tolerance": null,
        "end_a": "male_npt",
        "end_b": "chamfer",
        "quantity": 2,
        "in_research_scope": true,
        "clarifications": [
          "End A: male 3/4–14 NPT requested. Confirm thread acceptance criteria and use dies designed for plastic. \n\nRule: GF Harvel S1 specifies a 50% reduction of the manufacturer’s plain-end water-service pressure rating at 73°F when cutting threads into suitable Schedule 80-or-heavier PVC/CPVC IPS pipe.\n\nReference examples: ½-inch Schedule 80 is 850 × 0.50 = 425 psi; ¾-inch Schedule 80 is 690 × 0.50 = 345 psi, before other applicable reductions. These reference calculations do not establish a finished component or system rating.\n\nLimitations: Confirm manufacturer, product, temperature, conveyed substance, concentration, operating pressure and connection limitations. This rule does not apply universally to every plastic or to molded threaded fittings. Cut threads only on suitable Schedule 80 or heavier IPS pipe; do not cut NPT threads on Schedule 40 or CTS tubing. Specify ASME B1.20.1 / ASTM F1498 dimensions and gaging; F1498 is not pressure certification.",
          "End B chamfer: specify joining purpose, angle and whether a dimension is axial extent or radial removal. \n\nRule: Follow the selected manufacturer’s product- and size-specific end-preparation instructions.\n\nSource example: IPEX S12, printed pages 47 and 51 (PDF pages 56 and 60), shows a 10–15 degree OD bevel with approximately 3/32 inch (0.09375 inch) AXIAL EXTENT, measured along the pipe axis, not radial depth. The accompanying instructions address pressure pipe 2 inches and above.\n\nLimitations: Do not assign this geometry by default to the ½-inch or ¾-inch examples. Confirm achievable chamfer dimensions with the selected manufacturer or fabricator. The undimensioned chamfer drawing illustrates shape only.",
          "Ask for required finished-length tolerance.",
          "Confirm product documents, finished-component application limits and the required process capability.",
          "Ask for conveyed substance, concentration, operating temperature and pressure; no material is selected from a vague application label.",
          "Schema success records structure only, not completeness, suitability or manufacturability."
        ],
        "source_refs": [
          "https://www.gfps.com/content/dam/gfps/us/other/archive/gfps-us-brochure-Vinyl-Catalog-and-Tech-Information-2024-en.pdf"
        ],
        "original_request": "Two pieces of three-quarter-inch nominal IPS Schedule 80 CPVC, 8 inches finished end-to-end, male 3/4–14 NPT on end A, chamfer on end B.",
        "sdr": null,
        "application": null
      }
    },
    {
      "id": "ambiguous-cpvc",
      "title": "An incomplete half-inch CPVC request",
      "request": "I need half-inch CPVC, cut to six inches and threaded.",
      "specification": {
        "material": "CPVC",
        "nominal_size": null,
        "sizing_system": null,
        "actual_od_requirement": null,
        "schedule": null,
        "finished_length": {
          "value": 6,
          "unit": "in"
        },
        "required_tolerance": null,
        "end_a": null,
        "end_b": null,
        "quantity": null,
        "in_research_scope": true,
        "clarifications": [
          "Confirm what “half-inch” means: a nominal designation or an actual measured dimension. If nominal, confirm IPS or CTS. Reference half-inch IPS Schedule 80 OD is 0.840 inch; CTS CPVC SDR 11 OD is 0.625 inch. Do not assume either interpretation or system.",
          "Confirm the schedule or tubing series and product specification.",
          "Is six inches the finished end-to-end length after end treatments?",
          "Which end or ends require threads? Confirm designation and acceptance criteria; Do not cut NPT threads on CTS tubing.",
          "What treatment is required on any plain end?",
          "How many pieces and what finished-length tolerance?",
          "Ask for conveyed substance, concentration, operating temperature and pressure; no material is selected from a vague application label.",
          "Schema success records structure only, not completeness, suitability or manufacturability."
        ],
        "source_refs": [
          "https://www.gfps.com/content/dam/gfps/us/other/archive/gfps-us-brochure-Vinyl-Catalog-and-Tech-Information-2024-en.pdf",
          "https://store.astm.org/d2846_d2846m-24.html",
          "https://www.spearsmfg.com/super_sourcebook/SSB-1%20Part%202%20Technical%20Information%20Catalog/082%20CPVC%20CTS%20Pipe,%20Fittings%20&%20Valves%20Design%20&%20Installation.pdf"
        ],
        "original_request": "I need half-inch CPVC, cut to six inches and threaded.",
        "sdr": null,
        "application": null
      }
    }
  ]
}
